][
] 
[12401] Lower wishbone front, left
Partnumber: 12401
|
This Lower Wishbone is made from high quality Alloy. It is lightweight, stiff and durable. We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with all needed assembling materials. |
[12402] Lower wishbone, right
Partnumber: 12402
|
This Lower Wishbone is made from high quality Alloy. It is lightweight, stiff and durable. We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with all needed assembling materials. |
[12403] Upper wishbone, front
Partnumber: 12403
|
On this wishbone we added an extra support for your plastic ballbearing, see the extension at the end of the wishbone. This extension will prevent damage of your bearing in most crashes. You can race on instead of doing any repair! All needed assembling materials are included. |
[12404] Front axle mount A
Partnumber: 12404
|
This front axlemount will form a stable front part of your car with the connection to your wishbones. We used here the same bearings as in the wishbones for minimum friction and no maintenance. The part comes with a complete set of assembling materials. |
[12405] Front axle mount B
Partnumber: 12405
|
Together with front axle A it will form a stable front part of your car with the connection to your wishbones. High quality bearings are used, resistant against dirt and water on a teflon base for minimum friction. The part comes with a complete set of assembling materials. |
[12406] Upright front, left
Partnumber: 12406
|
The upright left side is light weight. The size is smaller than the standard uprights, smaller bearings are required. The steering arm is fixed with only one bolt as it fits as a puzzle in the upright. Technically the geometry is changed as the points for mounting onto the upper and lower wishbone are shifted by 3mm from each other, this improves the steering of your car. Assembling materials and the stainless steel distance bush are included (excluded bearings). We recommend to use bearing: 18700. The brakes can be mounted on the front of the upright. |
[12407] Upright front right
Partnumber: 12407
|
The upright right side is light weight. The size is smaller than the standard uprights, smaller bearings are required. The steering arm is fixed with only one bolt as it fits as a puzzle in the upright. Technically the geometry is changed as the points for mounting onto the upper and lower wishbone are shifted by 3mm from each other, this improves the steering of your car. Assembling materials and the stainless steel distance bush are included (excluded bearings). We recommend to use bearing: 18700. The brakes can be mounted on the front of the upright. |
[12451] Lower wishbone front, left - XL
Partnumber: 12451
|
This lower wishbone is the XL version of the standard wishbone for the Leopard. The wider wheelbase makes the car more stable, width approximate 475mm (depending on installed camber, toe-out). We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with assembling material. |
[12452] Lower wishbone front, right - XL
Partnumber: 12452
|
This lower wishbone is the XL version of the standard wishbone. The wider wheelbase makes the car more stable, width approximate 475mm (depending on installed camber, toe-out). We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with assembling material. |
[12453] Upper wishbone front - XL
Partnumber: 12453
|
This is the wider version of the standard wishbone. It makes the car approximately 475mm wide and more stable to drive. Of course the support for your plastic ballbearing is also made on this wishbone. Assembling materials are included. |
[18406] Wheel axle, front (short)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 52,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18407] Wheel axle, front (medium)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 57,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18408] Wheel axle, front (long)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 62,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18409] Wheel axle, front (extra long)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 67,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18410] Servo Saver
|
The servo saver is silky smooth in operation and enables you to fine tune your steering geometry by the use of several options for locating the track-rods and the servo linkages. The force required to enable the servo saver is the same in either direction and the spring tension is fully adjustable. An extra spring is included for those who run an extra strong servo, eg the Tonegawa. For the Leopard an extra collet is needed to mount the servo saver, ask your dealer for part number: 18410-05. Click here for a small animation film. |
[18700] Bearings - 8x16x5mm
|
The roller bearings have a rubber seal to protect the bearings from dirt and sand. Size (inside diameter x outside diameter x width): 8x16x5mm. We recommend you to use these light running bearings in the uprights. Packed as a set of 4 bearings. |
[18801] Fixation bolt for stabi
Partnumber: 18801
|
To fix your stabilization bar on the wishbones use these bolts. Double click the picture to take a closer look. Can be used on the Leopard and the Touringcar series. |
[18806] Distance bush
|
Distance bush made from stainless steel. Unlikely the usual alloy bushes this part won't be pressed together when mounted on the car. Can be used on all types of cars. |
[18813] Shocker quick mount
|
The shocker quick mount is easy to put on and makes quick removal of the shocker possible. Delivered as a pair. Made from stainless steel the part is protected against corrosion. Bolts and special clips are included. The clips can be assembled easy as 1,2,3 by hand! |
[18815] Shafts for wishbones
|
Stainless Steel shafts for mounting your wishbones. No corrosion after driving in wet conditions by using these Stainless Steel shafts. The shafts are delivered as a pair with the needed clips. Total length: 79.5mm |
