][
] 
[13400] front-end Marder
|
This set includes the parts 13401 until 13408. The set includes all important parts to beef up the front end your Marder against a strongly reduced price. See for info on the parts each seperate part listed below. All assembly material is included, but excl the bearings. |
[13401] Lower Wishbone Front, Left
|
This Lower Wishbone is made from high quality Alloy, the wishbone is therefor light weight, stiff and durable. The wishbone has teflon bearings: resistant against high pressure, dirt and water. Maintenance or lubrication is not needed. The wishbone is fully exchangeable and is delivered with assembling material. |
[13402] Lower wishbone front, right
|
This Lower Wishbone is made from high quality Alloy, the wishbone is therefor light weight, stiff and durable. The wishbone has teflon bearings which are resistant against high pressure, dirt and water. The bearings do not need any maintenance or lubrication. The wishbone is fully exchangeable and is delivered with assembling material. |
[13403] Upper wishbone front
|
Just as the lower wishbones only the best material is used for this product. We added as an extra the support for your bearing, see the extension at the end of the wishbone. This will prevent damage of your bearing in (almost) every crash, you will be able to race on instead of doing any repair! The part is delivered with a complete set of assembling materials. |
[13404] Bulk head A
|
This front axlemount has an open space to mount the stabilization bar if desired. We pressed in the same bearings as used in the wishbones for minimum friction and no maintenance. All needed assembling materials will be included. |
[13405] Bulk head B
|
If you say A than B should follow. Together with the Front Axle Mount A this part will get the best out of the driver and the car. The parts form a solid and stiff base which will give maximum control over the car. The part is delivered with a complete set of assembling materials. |
[13406] Height Adjustment
|
Not strictly necessary but designed for those who want to tune their car till the last drop. No terrain will be feared as you can adjust the height with this item easily. Where possible we machined away material without any compromise to strength. The part comes with a complete set of assembling materials. |
[13407] Shockmount plate front
|
A fine piece of technique. The brake cable holder can be mounted in the desired angle to the right or left side. This will reduce friction of your braking cables to a minimum giving you a optimum control over your car. Delivered together with a complete set of assembling materials. |
[13408] Shockmount front
|
Lightweight tuning without any compromise to stiffness and durability. You can change the position (more or less vertical) of the shockabsorber according to the track conditions. Delivered together with a complete set of assembling materials. |
[13409] Brakecable holder
|
Easy to mount and adjust into the right angle onto partnumber 13407. Your brakecables will be guided smoothly for an optimal brake-control over your car. Completely delivered with a set of assembling material. |
[13413] Stabilization bar, front
|
This stabilization bar is made of stainless spring steel. The bar is most effective on less accidented terrain and at higher driving speed. The stabilization bar is delivered with assembling material, exclusive the plastic joint FG 7071/2. |
[13414] Body Mount MB
Partnumber: 13414
|
The mount for the body posts for the MB can fit 15 degrees left, right or straight onto partnumber 13407. This will allow you to choose the placement of your servo's. The holes for fixing your brake cables are already integrated. Partno 13409 is not needed. Completely delivered with a set of assembling material. |
[13451] Lower wishbone, left - XL
|
This lower wishbone is the XL version of the standard wishbone for the Marder. The wider wheelbase makes the car more stable. We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with assembling material. A 15mm longer steering rod is required. |
[13452] Lower wisbone, right - XL
|
This lower wishbone is the XL version of the standard wishbone for the Marder. The wider wheelbase makes the car more stable. We pressed in the best teflon bearings, resistant against dirt, water and high loads. Maintenance or lubrication is not needed. The wishbone is delivered with assembling material. A 15mm longer steering rod is required. |
[13453] Upper wishbone XL
|
The wide version of the upper wishbone. Use in combination with 13451/13452. The car will have a wider wheelbase this will add stability to the car and improve performance. |
[18402] Upright left, front
|
The upright left side is light weight. The size is smaller than the standard uprights, smaller bearings are required. The steering arm is fixed with only one bolt as it fits as a puzzle in the upright. Technically the geometry is changed as the points for mounting onto the upper and lower wishbone are shifted by 3mm from each other, this improves the steering of your car. Assembling materials and the stainless steel distance bush are included (excluded bearings). We recommend to use bearing: 18700. |
[18403] Upright right, front
|
The upright right side is light weight. The size is smaller than the standard uprights, smaller bearings are required. The steering arm is fixed with only one bolt as it fits as a puzzle in the upright. Technically the geometry is changed as the points for mounting onto the upper and lower wishbone are shifted by 3mm from each other, this improves the steering of your car. Assembling materials and the stainless steel distance bush are included (excluded bearings). We recommend to use bearing: 18700. |
[18406] Wheel axle, front (short)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 52,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18407] Wheel axle, front (medium)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 57,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
[18408] Wheel axle, front (long)
|
The wheel axle is made from Stainless Steel, is reinforced and precision grinded. Thus: no corrosion, improved mechanical characteristics and it fits like a glove. Length: 62,5mm A special nut with a ripped flange will lock the wheel. The small bolt with the flange on the backside will hold the axle in place. Sold as a set. |
