End cap of the shock absorber, top.
Fits shockers 12300 & 12320

Closing lid for the shock absorbers 12300 & 12320.

Adjusting ring to change the ride height / pre-load on the shocker spring.
Fits shockers 12300 & 12320.

Housing of the shock absorber 12320.

Piston for shockabsorber 12300 & 12320.
Specify desired hole size at order.
Size 1.5mm is standard.

Sold per piece.

Spring disc for shock absorbers 12300 & 12320.

Volume compensation for the standard shocks.
Fits shock 12320

Universal shock absorber. These shockers are the same size as standard FG shockers for the rear but they are NOT leaking !
Travel (100~144mm) of this universal shocker is enlarged by 10% in the same length !

A special teflon coating is used on the shocker housing for low friction and to reduce wear to a minimum.
The rounded shaped piston with a precise fit provides a minimum contact surface for even less friction & wear.

The piston rod is hardened and presicely grinded and will not corrode.
The special seal at the bottom provides a fully closed shocker even in harse dusty conditions.
But not only does it close the shocker.
It is selected also as the "stick-slip" resistance is significant lower as other currently used seals.
The dampening proces is therefor more true; and not influenced by high friction like o-rings cause.
A low friction piston together with low friction seal ensures an optimal dampening proces.

As there is no leakage of oil, there can also not come any air into the oil medium.
The shock absorber therefor does not get soft or feels like a sponge, but remains stabil as set at the start.
Also after half an hour of non-stop driving.
The spring disc allows maximum travel as the dirt scraper fits in the disc at full compression.

Travel: 100-144mm
Click here for assembly instructions.
Or click here for a small assembly animation.
Sold as a set (2 pcs), springs are not included.

10 pcs of bodyclips.

Flexible spoiler.
Fits all cars.
Holes for the spoiler carrier you need to drill yourself.

Piston rod for the shockabsorber.
Fits shockabsorber 18320 and 12320.

Volume comensation foam, 6mm thick.
For high volume shockabsorber 18320.

Shockabsorber springs 100mm length.
Select the desired wire diameter.

Universal shock absorber for the rear.
These shockers are high volume shockers and are NOT leaking !
Travel of this universal shocker is enlarged by 10% in the same length !
100-144mm travel length.
Click here for a small animation film.

A special teflon coating is used on the shocker housing for low friction and to reduce wear to a minimum.
The rounded shaped piston with a precise fit provides a minimum contact surface for even less friction & wear.

The piston rod is hardened and presicely grinded and will not corrode.
The special seal at the bottom provides a fully closed shocker even in harse dusty conditions.
But not only does it close the shocker.
It is selected also as the "stick-slip" resistance is significant lower as other currently used seals.
The dampening proces is therefor more true; and not influenced by high friction like o-rings cause.
A low friction piston together with low friction seal ensures an optimal dampening proces.

As there is no leakage of oil, there can also not come any air into the oil medium.
The shock absorber therefor does not get soft or feels like a sponge, but remains stabil as set at the start.
Also after half an hour of non-stop driving.
The spring disc allows maximum travel as the dirt scraper fits in the disc at full compression.

Travel: 100-144mm
Click here for assembly instructions.
Sold as a set (2 pcs).

60ml of very thin silicon oil.

All shock absorbers of Elcon use just 1 type of silicon oil which is very thin.
The complete concept behind using only 1 single type of thin oil is as simple as effective.

Oil warms up during driving.
A thick oil would under influence of the rising temperature go down in viscosity. The damper setting changes noticeable.
An oil that is already thin from the start will change far less under influence of heath in viscosity.

The silicon oil we have chosen is this "thin" so you won't experience any noticeable change in the car set-up after running through a complete tank of fuel.
The car feels the same throughout the complete run.

We advise to use this type of silicon oil in all Elcon shock absorbers.
To change the damping can be done by changing the inner piston of the shock absorber. It is not only more effective it is also cost saving.

Set of drive shafts in XL length (106,5mm).
Including steel balls and conical springs.

Set of rubber seal caps for sealing your ball drive system.
Protects your ball drive system against sand, dirt etc.

4 pcs of clutch shoes for the teflon clutch.